Blog

Is your electrical substation really safe? A practical guide and electrical safety checklist for EHS team

European statistics reveal a serious paradox: while the overall industrial accident rate is decreasing, the number of fatal accidents in electrical installations is increasing. Up to 90% of incidents and near-misses in facilities remain unreported, creating a false sense of security. No formal paper audit can guarantee that substation safety will truly prevent technical or human failure.

True prevention requires continuous verification of the technical integrity of protective barriers directly in the field. This engineering guide combines legislative obligations, hidden physical threats, and certified materials into a practical checklist.

Legislative and normative framework: Responsibilities, inspections, and penalties

The operation of electrical substations is subject to strict legal regulations and binding technical standards. The fundamental pillar in Slovakia is Act No. 124/2006 Coll. on Occupational Safety and Health (OSH). This is directly followed by the Decree of the Ministry of Labour, Social Affairs and Family of the Slovak Republic No. 508/2009 Coll. for classified technical equipment.

  • Categorization of equipment and demonstrable professional competence of personnel.
  • Compliance with prescribed deadlines for professional inspections and official tests.
  • Implementation of technical barriers and safe procedures according to the STN EN 50110-1 standard.

EHS teams bear direct responsibility for the safe condition of the entire electrical infrastructure. Neglecting these duties results in high fines and personal criminal liability for management. A thorough knowledge of legislation is therefore the foundation of any functional accident prevention.

Classification of classified technical equipment and personnel qualifications (Decree No. 508/2009 Coll.)

Under Slovak legislation, electrical substations are categorized as classified technical equipment with a high level of risk. Group A high-voltage installations require official tests, while standard Group B low-voltage distribution systems do not.

Section

Qualification Level

Scope of competencies in the substation

§ 21

Electrician (Elektrotechnik)

Work on installations only under the supervision of more experienced persons.

§ 22

Independent Electrician

Independent work on equipment and management of unqualified workers.

§ 23

Electrician for Operation Management

Operation management and coordination of teams on extensive installations.

§ 24

Inspection Technician

Performing professional inspections and tests (OPaOS) and issuing official inspection reports.


Workers without an electrical qualification certificate must never enter the open bays of switchboards. Strict adherence to these levels protects the facility from unauthorized interventions and fatal accidents.

Deadlines for inspections (OPaOS) and financial/criminal impacts of neglecting OSH

The basic deadlines for inspections of electrical substations are strictly determined by Annex No. 8 of Decree No. 508/2009 Coll., depending on the nature of the environment. The standard five-year interval for professional inspections and official tests (OPaOS) is reduced to three, two, or one year in aggressive, dusty, or humid environments. In practice, the shortest specified deadline always applies unless the technology manufacturer has set stricter conditions.

For missing inspections of electrical classified equipment, the Labour Inspectorate can impose a fine of up to 100,000 EUR, while in the case of a fatal accident, the law imposes a penalty ranging from 33,000 to 200,000 EUR. Neglecting these obligations establishes the direct criminal liability of the management (Sections 147 and 158 of the Criminal Code) and entitles the insurance company to reduce or completely refuse the insurance payout.

Hidden physical risks in the substation: Arc flash and step voltage

Electrical risks in a substation are treacherous because voltage cannot be seen, heard, or smelled. Technicians' awareness often focuses only on direct electric shock. However, dynamic physical phenomena during short circuits and ground faults pose the most serious threat to health.

  • Thermal radiation of plasma with a core temperature of up to 20,000 °C.
  • Blast pressure wave accompanied by extreme acoustic shock exceeding 140 dB.
  • Dangerous soil potential gradient in the form of step and touch voltage.

These destructive processes occur in fractions of a second without any warning. Effective protection therefore requires rigorous modeling of destruction zones and reliable galvanic isolation of the worker.

Arc Flash and incident energy calculation according to IEEE 1584-2018

An arc flash represents an extreme physical threat with plasma temperatures reaching up to 20,000 °C. The vaporization of copper creates a massive blast wave (Arc Blast) with an acoustic shock over 140 dB. Thus, an electrical arc (Arc Flash) radiates devastating thermal energy in a split second.

Electrode Configuration (IEEE 1584)

Risk and plasma behavior

VCB (Vertical conductors in a metal box)

Standard energy radiation inside the switchboard.

HCB (Horizontal conductors in a metal box)

Highest risk; plasma is directed straight at the technician like a flamethrower.

VOA (Vertical conductors in open air)

Typical for outdoor installations with faster dispersion of heat flux.


The threshold for irreversible 2nd-degree burns is an incident energy of 1.2 cal/cm². This value precisely defines the safe working distance – the Arc Flash Boundary. The paradox is that a lower fault current often delays the protection response, which dangerously prolongs the arc burning time and increases the total thermal exposure.

Step and touch voltage vs. grounding limits (STN EN 50522)

When a fault short-circuit current dissipates into the ground, a dangerous potential funnel is created on the floor surface. This phenomenon generates dangerous step and touch voltage with the risk of electrical current flowing directly through the human body. Even the prescribed grounding resistance of up to 2 Ω will not prevent the transfer of induced potential during a massive fault.

Therefore, even the correct grounding of a transformer station according to the STN EN 50522 standard does not guarantee zero risk of injury in the current dissipation zone. The technician's life can only be reliably protected by additional galvanic isolation from the ground, which interrupts the current path between hand and foot.

Safe working procedures and LOTO (STN EN 50110-1)

The binding standard STN EN 50110-1 (Operation of electrical installations) sets a strict procedure before starting work on equipment. The transition to a dead (de-energized) state requires the unconditional observance of the five safety rules for electricians:

  1. Complete disconnection of the equipment from all power sources with a visible break in the circuit.
  2. Physical securing against reconnection using safety hasps and padlocks.
  3. Reliable verification of the dead state exclusively with a calibrated and tested voltage tester.
  4. Proper grounding and short-circuiting of all affected phase conductors with portable kits.
  5. Barricading and safe covering of adjacent components that remain live.

To prevent the accidental energization of the switchboard by another shift, the LOTO (Lockout/Tagout) safety system is applied. Every technician is required to use a padlock with a unique key (Keyed Different mode) and a clear name tag.

Electrical insulating matting (IEC 61111:2009) as the first line of collective protection

While arc flash suits protect personnel from extreme heat, they do not stop current from flowing through the body. Certified electrical insulating matting, therefore, forms the basis of passive collective protection in every substation.

Type of protection

Applicable standard

Primary protective purpose

Electrical insulating matting

IEC 61111:2009

Galvanic isolation from the floor and elimination of step voltage.

Dielectric gloves

IEC 60903

Hand protection against touch voltage when handling components.

Arc flash clothing

IEC 61482-2

Thermal barrier against plasma and burns without isolation from the ground.


Thanks to vulcanization in rotary presses, BOGUMA mattings achieve complete material homogeneity without hidden cavities and bubbles. These electrical insulating mattings reliably interrupt the hand-to-foot electrical path and protect personnel from electric shock.

Matting classes (DEK0 to DEK4) and the fatal mistake in working vs. test voltage

The international standard IEC 61111:2009 divides floorings into classes DEK0 to DEK4 with mandatory color coding. A key parameter is the working vs. test voltage, which buyers often fatally confuse. The working voltage guarantees permanent safety, while the higher test voltage only verifies the flawlessness of production.

For installations with a voltage of 22 kV, you must therefore not use a Class 2 mat with a working limit of up to 17 kV. The only safe choice in accordance with the standard remains a Class 3 electrical insulating matting with a limit of up to 26.5 kV. For the highest voltage loads up to 36 kV, a Class 4 electrical insulating matting is designed.

Polymer chemistry according to the environment: SBR, NBR, or EPDM?

The dielectric strength of insulating flooring directly depends on its ability to withstand chemical and physical environmental influences. Choosing the right elastomer compound prevents undesirable degradation and sudden failure of the dielectric.

  • SBR (Styrene-butadiene): Offers high resistance to mechanical abrasion in dry indoor substations with frequent operator movement.
  • NBR (Nitrile): This oil-resistant NBR electrical insulating matting (Category H) prevents dangerous rubber swelling caused by lubricant leaks from transformers.
  • EPDM (Ethylene-propylene): A special ozone-resistant EPDM electrical insulating matting (Category Z) eliminates the devastating effect of ozone and UV radiation on insulating mats in outdoor stations and withstands frost down to -40 °C (Category C).

In addition, high-quality compounds achieve a Cfl-s1 fire classification with limited toxic smoke generation. Properly selected rubber thus reliably guarantees the safety of personnel in specific operating conditions.

Installation, ergonomics, and why electrical insulating matting must not be fully glued

The question of why an electrical insulating mat must not be glued to the floor is a key point during professional inspections. Permanent gluing prevents inspection of the underside of the mat and promotes capillary rising damp. Each dielectric strip must remain uniquely identifiable, which is ensured by the IEC marking vulcanized directly into the material.

BOGUMA Pattern Type

Main application and ergonomic benefits

Pattern S1 (Corrugated / wide ribbed)

Effectively drains liquids and allows for easy sweeping of dirt.

Pattern S7 (Fine ribbed)

Provides stable support, reduces foot fatigue, and is suitable for dry halls.

Pattern S8 (Coin pattern)

Offers omnidirectional traction and high abrasion resistance in corridors.

Smooth H0/H1

Facilitates immediate disinfection in sterile laboratories and server rooms.


A high-quality electrical insulating matting with an anti-slip finish effectively prevents falls and reduces personnel fatigue during long periods of standing. Certified industrial floorings, which offer a wide selection of material compounds and surface patterns, are intended for the most demanding operations.

Protection during live working: Electrical insulating blankets (IEC 61112:2009)

When working in confined switchboards, there is a risk of unintentional contact of hands or tools with live parts. Effective temporary protection in these cases is provided by a certified electrical insulating blanket according to the IEC 61112:2009 standard. This mechanical barrier enables safe live-line maintenance on low-voltage equipment without interrupting operations.

The EIP0 Class 0 electrical insulating blanket, intended for live working up to 1,000 V, meets all practical requirements. The material thickness of 1.0 to 1.5 mm guarantees low weight and high flexibility, even when tightly wrapping busbars. The distinctive salmon-orange color ensures immediate visibility of the work zone, and the polymer used reliably resists both acids and ozone.

Degradation, maintenance, and discard criteria for insulating equipment

Proper cleaning and storage of electrical insulating mattings directly determine the preservation of their insulation resistance. Clean the mats exclusively with a neutral soap solution and let them air dry at a temperature not exceeding 65 °C. Aggressive solvents, gasoline, or wire brushes will irreversibly degrade the elastomer.

  • Ozone and UVC radiation from germicidal lamps damage electrical insulating mats made of standard SBR rubber. Therefore, cover the floorings or remove them from the room before such disinfection.
  • A thorough visual inspection before every shift reveals cuts, punctures, blisters, and trapped metal shavings.
  • Periodic laboratory tests according to the IEC 60243-1 standard verify the real dielectric strength of the material as it ages.

Safety regulations state exactly when a damaged electrical insulating matting must be discarded. Upon discovering a cut, swelling from oil, or an illegible marking, immediately dispose of the material and physically cut it in half. This prevents its accidental return to the workplace.

Practical Substation Electrical Safety Checklist for EHS

This checklist serves EHS teams for systematic verification of safety in an electrical substation. It facilitates internal auditing and helps uncover critical risks even before labour inspectors arrive.

Audit Area

Parameter Monitored

Acceptance Criterion for Compliance

1. Documentation & personnel

Validity of inspections and operator certificates

Recorded valid OPaOS reports and electrician qualifications according to §§ 21 to 24.

2. Floor insulation

Class and condition of electrical insulating mattings

Correct IEC 61111 class without gluing, with legible vulcanized tape and an overlap of min. 1 m.

3. LOTO procedures

Locking of switching elements

Availability of Keyed Different padlocks, hasps, and properly filled-out name tags.

4. Arc Flash & Live-line

Protection against arc flash and live parts

Marked Arc Flash Boundary, certified suits, and flexible EIP0 blankets (IEC 61112).

5. Environment & maintenance

External influences and sterilization

Exclusion of leakage moisture and strict protection of SBR rubber from direct UVC radiation and ozone.


Regular evaluation of these points creates a reliable electrical safety audit checklist in a manufacturing plant. This ensures permanent compliance with standards and reliable protection of technicians.

Do not leave the safety of your substation to chance or formal inspections.

Prepare your workplace for the strict requirements of labour inspection and protect your team from fatal electrical risks. At BOGUMA, we manufacture certified electrical insulating mattings (Classes 0 to 4) and electrical insulating blankets according to the applicable international standards IEC 61111 and IEC 61112.

Request a free technical consultation and a tailored quote directly at BOGUMA.sk

Frequently Asked Questions (FAQ)

1. What is the fundamental difference between the working and test voltage of an electrical insulating mat?

The working voltage represents the maximum continuous operating load guaranteeing personnel safety, while the higher test voltage serves only for short-term laboratory verification of product flawlessness during manufacturing.

2. What class of electrical insulating matting must we choose for a standard 22 kV industrial substation?

For a 22 kV installation, you must unconditionally select Class 3 according to IEC 61111 with a working limit of up to 26.5 kV, because Class 2 provides permanent protection only up to 17 kV.

3. Why do OSH inspectors and technicians advise against fully gluing electrical insulating mats to the floor?

Gluing the flooring prevents visual inspection of the mandatory vulcanized marking on the back of the material and creates space for dangerous capillary trapping of leakage moisture under the mat.

4. Will an electrical insulating matting protect a worker from the effects of an electrical arc (Arc Flash)?

The electrical insulating matting isolates personnel's feet exclusively from the galvanic passage of current to the ground, whereas only certified clothing according to IEC 61482-2 protects against the extreme temperature and pressure of an arc.

5. Can routine room disinfection using an ozonator or a germicidal UVC lamp damage rubber mats?

Concentrated ozone and hard UVC rays cause rapid oxidative degradation and cracking of standard SBR rubber; therefore, always remove the floorings or cover them opaquely before sterilization.

6. What is an electrical insulating blanket used for, and when is it mandatory?

A certified Class 0 blanket creates a temporary mechanical and insulating barrier over exposed live parts up to 1,000 V during live working in confined switchboards.

7. When must an electrical insulating matting be immediately removed from operation in a substation?

Immediately discard and physically cut the material in half if there is a mechanical cut, puncture, swelling from aggressive oil, blisters from a short circuit, or if the marking becomes illegible.